SE-400 C AUSWERTEGERAET

Бренды по алфавиту:

Eng Рус

Производитель: Schmersal GmbH

Артикул: Л-0045832

Работаем с юридическими лицами, бюджетными организациями, ИП

По вопросам приобретения товара пишите на zakaz@lanfor.ru

Оплата по безналичному расчету согласно выставленному счету

Самовывоз - бесплатно, от 300руб. до пункта выдачи в Вашем городе, доставка от 500руб. "до двери"

Certificates	TÜV cULus EAC

Standards	EN ISO 13850 EN ISO 13849-1
Climatic stress	EN ISO 13856-2
Enclosure material	Plastic, PE (Black), Crastin (Grey)
Gross weight	184 g
Time to readiness, maximum	32 ms
Reaction time, maximum	32 ms

Stop-Category	0
Electronic Fuse	Yes
Wire breakage detection	Yes
Short-circuit recognition	Yes
Start input	Yes
Feedback circuit	Yes
Automatic reset function	Yes
Reset edge detection	Yes
Reset after disconnection of supply voltage	Yes
Earth connection detection	Yes
Integral System Diagnostics, status	Yes
Number of LEDs	2
Number of undelayed semi-conductor outputs with signaling function	1
Number of safety contacts	2
Number of signalling outputs	1

Performance level, up to	e
Control category to EN13849	4
Control category to EN954	4
PFH-value	2.47 x 10⁻⁸ /h
Note (PFH-value)	up to max. 50,000 switching cycles/year
Mission Time	20 Year(s)

Mechanical life, minimum	30,000,000 Operations
Mounting	Snaps onto standard DIN rail to EN 60715

Terminal Connector	Screw connection
Length of cable	200 m
Cable section, maximum	2 x 1.5 mm²
Note (Cable section)	All indications about the cable section are including the conductor ferrules.

Degree of protection of the enclosure	IP40
Degree of protection of the mounting space	IP54
Degree of protection of clips or terminals	IP20
Ambient temperature, minimum	+5 °C
Ambient temperature, maximum	+55 °C
Resistance to vibrations to EN 60068-2-6	10 … 55 Hz, amplitude 0.15 mm

Rated impulse withstand voltage U_imp	4 kV
Overvoltage category	III
Degree of pollution to VDE 0110	2

Rated operating voltage	24 VDC +20% / -10%
Operating current	150 mA
Rated AC voltage for controls at DC minimum	21.6 VDC
Rated control voltage at DC, maximum	28.8 VDC
Utilisation category AC-15	230 VAC
Utilisation category AC-15	2 A
Utilisation category DC-13	24 VDC
Utilisation category DC-13	3 A
Electrical power consumption, maximum	4 W

EMC rating	EMC-Directive

Indicated operating states	Safety edge function

Note (applications)	Safety edges

Note (General)	The overall machine safety depends on the professional mounting and installation of the safety monitoring module and the signal transmitter, as well as on the correct and professional electrical connection of the components. If there it any risk whatsoever, the machine may not be restarted.

Note (Wiring diagram)	A Start-Reset-Taster (S) can optionally be connected to the feedback circuit. Both re-initialisation and auto-reset must comply with the requirements of EN 1760-2 (diagram A2, A3). The wiring diagram is shown for the de-energised condition. Monitoring the safety edges SE 40 / SE 70 with a safety monitoring unit SE-400C up to PL e and Category 4. The feedback circuit monitors the position of the contactors KA and KB.