SE-304 C AUSWERTEGERAET

Бренды по алфавиту:

Eng Рус

Производитель: Schmersal GmbH

Артикул: Л-0045840

Работаем с юридическими лицами, бюджетными организациями, ИП

По вопросам приобретения товара пишите на zakaz@lanfor.ru

Оплата по безналичному расчету согласно выставленному счету

Самовывоз - бесплатно, от 300руб. до пункта выдачи в Вашем городе, доставка от 500руб. "до двери"

Certificates	TÜV EAC

Stop-Category	0
Electronic Fuse	Yes
Wire breakage detection	Yes
Short-circuit recognition	Yes
Start input	Yes
Feedback circuit	Yes
Automatic reset function	Yes
Reset edge detection	Yes
Reset after disconnection of supply voltage	Yes
Earth connection detection	Yes
Integral System Diagnostics, status	Yes
Number of LEDs	5
Number of undelayed semi-conductor outputs with signaling function	1
Number of safety contacts	1
Number of signalling outputs	1

Performance level, up to	d
Control category to EN13849	3
Control category to EN954	3
PFH-value	1.01 x 10⁻⁷ /h
Note (PFH-value)	up to max. 5,000 switching cycles/year
Mission Time	20 Year(s)

Mechanical life, minimum	10,000,000 Operations
Mounting	Snaps onto standard DIN rail to EN 60715

Terminal Connector	Screw connection
Length of cable	200 m
Cable section, maximum	2 x 1.5 mm²
Note (Cable section)	All indications about the cable section are including the conductor ferrules.

Degree of protection of the enclosure	IP40
Degree of protection of the mounting space	IP54
Degree of protection of clips or terminals	IP20
Ambient temperature, minimum	+5 °C
Ambient temperature, maximum	+55 °C
Resistance to vibrations to EN 60068-2-6	10 … 55 Hz, amplitude 0.15 mm

Rated impulse withstand voltage U_imp	4 kV
Overvoltage category	III
Degree of pollution to VDE 0110	2

Frequency range	50 Hz
Rated operating voltage	24 VDC +20% / -10% 24 VAC +10% / -10%
Operating current	500 mA
Rated AC voltage for controls, 50 Hz, minimum	21.6 VAC
Rated control voltage at AC 50 Hz, maximum	28.8 VAC
Rated AC voltage for controls at DC minimum	21.6 VDC
Rated control voltage at DC, maximum	28.8 VDC
Utilisation category AC-15	230 VAC
Utilisation category AC-15	2 A
Utilisation category DC-13	24 VDC
Utilisation category DC-13	2 A
Electrical power consumption, maximum	4 W
Pull-in delay at RESET	100 ms ... 2000 ms

EMC rating	EMC-Directive

Indicated operating states	Authorised operation fault indication

Note (applications)	Safety edges

Note (General)	The overall machine safety depends on the professional mounting and installation of the safety monitoring module and the signal transmitter, as well as on the correct and professional electrical connection of the components. If there it any risk whatsoever, the machine may not be restarted.

Note (Wiring diagram)	Both re-initialisation and auto-reset must comply with the requirements of EN 1760-2 (diagram A2, A3). The wiring diagram is shown for the de-energised condition. Monitoring the safety edges SE 40 / SE 70 with a safety monitoring unit SE-304C up to PL d and Category 3. Manual reset function or auto-reset: the manual reset function is triggered by an edge-sensitive signal (edge switching '0-1-0' within 100 ms up to 2 s) (X2/X3). Alternatively, the auto-reset function can be activated by a connection (A3/X2). If less than 4 safety edges are connected, the following diagram must be observed.