AST11 ST-AS6 | Ланфор

Бренды по алфавиту:

Eng Рус

Производитель: Schmersal GmbH

Артикул: Л-0043805

Работаем с юридическими лицами, бюджетными организациями, ИП

По вопросам приобретения товара пишите на zakaz@lanfor.ru

Оплата по безналичному расчету согласно выставленному счету

Самовывоз - бесплатно, от 300руб. до пункта выдачи в Вашем городе, доставка от 500руб. "до двери"

Certificates	cULus

Standards	IEC 61508 EN 60947-5-1 EN 50295 EN ISO 13849-1
Connector (electric)	Sensor connection: pre-wired cable 6-pole AS-i connection: connector plug M12, 4-pole
Enclosure material	Plastic, glass-fibre reinforced thermoplastic, self-extinguishing
Gross weight	120 g

Short-circuit recognition	Yes
Integral System Diagnostics, status	Yes
Number of inputs for NC	1
Number of inputs for NO	1
Number of pre-wired cable	1

Standards

IEC 61508

Performance level, up to

Control category to EN13849

PFH-value

2.04 x 10⁻⁹ /h

Safety Integrity Level (SIL), suitable for applications in

Mission Time

20 Year(s)

Diameter of sensor	28 mm
Height of sensor	86.5 mm

Degree of protection	IP67 to EN 60529
Ambient temperature, minimum	-25 °C
Ambient temperature, maximum	+55 °C
Storage and transport temperature, minimum	-25 °C
Storage and transport temperature, maximum	+85 °C
Relative humidity, minimum	30 %
Relative humidity, maximum	95 %
Note (Relative humidity)	non-condensing
Protection rating	II

Rated insulation voltage U_i	32 VDC
Rated impulse withstand voltage U_imp	0.8 kV
Overvoltage category	III
Degree of pollution to VDE 0100	3

Operating Current	50 mA
Current consumption, maximum	500 mA

AS-i Operating voltage, minimum	26.5 VDC
AS-i Operating voltage AS-i maximum	31.6 VDC
Note (AS-i Operating voltage)	Protection against polarity reversal

AS-i Version	V 2.1
AS-i Profile	S-7.B.F.E
AS-i, IO-Code	0x7
AS-i, ID-Code	0xB
AS-i, ID-Code1	0xF
AS-i, ID-Code2	0xE
AS-i Input, Channel 1	Data bits DI 0 / DI 1 = dynamic code transmission
AS-i Input, Channel 2	Data bits DI 2 / DI 3 = dynamic code transmission
AS-i Outputs, DO 0	Solenoid control
AS-i Outputs, DO 1	No Function
AS-i Outputs, DO 2	No Function
AS-i Outputs, DO 3	No Function
AS-i Parameter bits, P0 ... P3	No function
Note (AS-i Parameter bits)	Set the parameter outputs to '1111' (0xF) FID: periphery error
AS-i Input module address	0
Note (AS-i Input module address)	Preset to address 0, can be changed through AS-interface bus master or hand-held programming device

Note (LED switching conditions display)	(1) LED green: Supply voltage (2) LED red: Communication error (3) LED yellow : Enabling status

Connection	AS-i connection
PIN 1	AS-i +
PIN 2	(Aux -)
PIN 3	AS-Interface -
PIN 4	(Aux +)
Connection	Sensor connection
PIN 1	Brown - Normally open contact (NO)
PIN 2	Blue - Normally open contact (NO)
PIN 3	White - Opener (NC)
PIN 4	Black - Opener (NC)
PIN 5	Red - Magnet (+) AUS
PIN 6	Grey - Solenoid GND