SRB320XV3 / V.2 | Ланфор

Бренды по алфавиту:

Eng Рус

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Стоимость уточняйте у менеджера

Производитель: Schmersal GmbH

Артикул: Л-0045705

Запросить цену

Работаем с юридическими лицами, бюджетными организациями, ИП

По вопросам приобретения товара пишите на zakaz@lanfor.ru

Оплата по безналичному расчету согласно выставленному счету

Самовывоз - бесплатно, от 300руб. до пункта выдачи в Вашем городе, доставка от 500руб. "до двери"

Level 1: Reset without edge detection, Optional Automatic reset function, Short-circuit recognition, Level 2: / Opener (NC) Normally open contact (NO)
Suitable for the signal processing of outputs with contact sensors
Suitable for signal processing of outputs connected to potentials (AOPDs), e.g. safety light grids/curtains
3 safety contacts, STOP 0, 2, safety contacts STOP 1

Ordering data

Product type description	SRB320XV3 / V.2
Article number (order number)	101195579
EAN (European Article Number)	4250116202171
eCl@ss number, Version 9.0	27-37-18-19
eCl@ss number, Version 11.0	27-37-18-19
ETIM number, version 6.0	EC001449
Replacement article number	101188433
Available until	31.12.2022

Approval - Standards

Certificates	cULus EAC

General data

Standards	IEC 61508 IEC/EN 60204-1 EN 60947-5-1 EN ISO 13849-1
Climatic stress	EN 60068-2-78
Enclosure material	Glass-fibre reinforced thermoplastic, ventilated
Material of the contacts, electrical	AgSn0, Ag-Ni, self-cleaning, positive drive
Gross weight	420 g

General data - Features

Stop-Category	0 1
Electronic Fuse	Yes
Wire breakage detection	Yes
Short-circuit recognition	Yes
Start input	Yes
Feedback circuit	Yes
Automatic reset function	Yes
Reset edge detection	Yes
Earth connection detection	Yes
Integral System Diagnostics, status	Yes
Number of LEDs	6
Number of openers	2
Number of safety contacts	5
Number of Safety contacts, STOP 0	3
Number of Safety contacts, STOP 1	2

Safety appraisal

Standards	EN 60947-5-1 IEC 61508

Safety appraisal - Relay outputs

Performance level, stop 0, up to	e
Performance level, stop 1, up to	d
Category, Stop 0	4
Category, Stop 1	3
Diagnostic Coverage (DC) Level, Stop 0	≥ 99 %
Diagnostic Coverage (DC) Level, Stop 1	>, 60
PFH-Value Stop 0	2.00 x 10⁻⁸ /h
PFH-Value Stop 1	2.00 x 10⁻⁷ /h
Safety Integrity Level (SIL), Stop 0, suitable for applications in	3
Safety Integrity Level (SIL), Stop 1, suitable for applications in	2
Mission time	20 Year(s)
Common Cause Failure (CCF), minimum	65
PFD value	5.30 x 10⁻⁵
PFD value	5.30 x 10⁻⁵

Mechanical data

Mechanical life, minimum	10,000,000 Operations
Mounting	Snaps onto standard DIN rail to EN 60715

Mechanical data - Connection technique

Terminal Connector	Screw connection rigid or flexible
Terminal designations	IEC/EN 60947-1
Cable section, minimum	0.25 mm²
Cable section, maximum	2.5 mm²
Tightening torque of Clips	0.6 Nm

Mechanical data - Dimensions

Width	45 mm
Height	100 mm
Depth	121 mm

Ambient conditions

Degree of protection of the enclosure	IP40
Degree of protection of the mounting space	IP54
Degree of protection of clips or terminals	IP20
Ambient temperature, minimum	-25 °C
Ambient temperature, maximum	+60 °C
Storage and transport temperature, minimum	-40 °C
Storage and transport temperature, maximum	+85 °C
Resistance to vibrations to EN 60068-2-6	10 ... 55 Hz, Amplitude 0.35 mm
Restistance to shock	30 g / 11 ms

Ambient conditions - Insulation value

Rated impulse withstand voltage U_imp	4 kV
Overvoltage category	III
Degree of pollution to VDE 0110	2

Electrical data

Frequency range	50 Hz 60 Hz
Rated operating voltage	24 VAC -15% / +10% 24 VDC -15% / +20%, residual ripple max. 10 %
Rated AC voltage for controls, 50 Hz, minimum	20.4 VAC
Rated control voltage at AC 50 Hz, maximum	26.4 VAC
Rated AC voltage for controls, 60 Hz, minimum	20.4 VAC
Rated control voltage at AC 60 Hz, maximum	26.4 VAC
Rated AC voltage for controls at DC minimum	20.4 VDC
Rated control voltage at DC, maximum	28.8 VDC
Electrical power consumption	2.6 W
Electrical power consumption	5.4 VA
Contact resistance, maximum	0.1 Ω
Note (Contact resistance)	in new state
Drop-out delay in case of power failure, typically	80 ms
Drop-out delay in case of emergency, typically	30 ms
Pull-in delay at automatic start, maximum, typically	250 ms
Pull-in delay at RESET, typically	20 ms

Electrical data - Safe relay outputs

Voltage, Utilisation category, AC15	230 VAC
Current, Utilisation category, AC15	6 A
Voltage, Utilisation category, DC13	24 VDC
Current, Utilisation category, DC13	6 A
Switching capacity, minimum	10 VDC
Switching capacity, minimum	10 mA
Switching capacity, maximum	250 VAC
Switching capacity, maximum	8 A

Electrical data - Safe relay outputs

Voltage, Utilisation category, AC15	230 VAC
Current, Utilisation category, AC15	3 A
Voltage, Utilisation category, DC13	24 VDC
Current, Utilisation category, DC13	2 A
Switching capacity, minimum	10 VDC
Switching capacity, minimum	10 mA
Switching capacity, maximum	250 VAC
Switching capacity, maximum	6 A

Electrical data - Digital inputs

Conduction resistance, maximum	40 Ω

Electrical data - Digital Output

Voltage, Utilisation category DC12	24 VDC
Current, Utilisation category DC12	0.1 A

Electrical data - Relay outputs (auxiliary contacts)

Switching capacity, maximum	24 VDC
Switching capacity, maximum	2 A

Electrical data - Electromagnetic compatibility (EMC)

EMC rating	EMC-Directive

Status indication

Indicated operating states	Position relay K2 Position relay K1 Internal operating voltage U_i Position relay K3

Other data

Note (applications)	Safety sensor Guard system Emergency-Stop button Pull-wire emergency stop switches Safety light curtain

Notes

Note (General)	Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit.

Circuit example

Note (Wiring diagram)	The wiring diagram is shown with guard doors closed and in de-energised condition. The control recognises cross-short, cable break and earth leakages in the monitoring circuit. 2 channel control shown for a guard-door monitor with two contacts, of which at least one contact has positive break, with external reset button (R). (H2) = Feedback circuit