ZQ 700 ST-AS | Ланфор

Бренды по алфавиту:

Eng Рус

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Стоимость уточняйте у менеджера

Производитель: Schmersal GmbH

Артикул: Л-0043765

Запросить цену

Работаем с юридическими лицами, бюджетными организациями, ИП

По вопросам приобретения товара пишите на zakaz@lanfor.ru

Оплата по безналичному расчету согласно выставленному счету

Самовывоз - бесплатно, от 300руб. до пункта выдачи в Вашем городе, доставка от 500руб. "до двери"

AS-Interface M12 connector, bottom
Thermoplastic enclosure
One tension force for cable lengths up to 10 m
Release push button
Position indicator
Twisting of towing eye not possible
wire pull and breakage detection
Double-insulated
Integrated AS-Interface
Suitable for AS-i Power24

Ordering data

Note (Delivery capacity)	Phased-out product
Product type description	ZQ 700 ST-AS
Article number (order number)	101215046
EAN (European Article Number)	4030661404455
eCl@ss number, Version 9.0	27-37-12-01
eCl@ss number, Version 11.0	27-37-12-01
ETIM number, version 6.0	EC002026
Available until	31.12.2020

Approval - Standards

Certificates	cULus ASi-SaW EAC

General data

Standards	IEC 61508 EN 60947-5-1 EN 50295 EN ISO 13850 EN ISO 13849-1
Enclosure material	Plastic, glass-fibre reinforced thermoplastic, self-extinguishing
Material of the cover	Plastic, glass-fibre reinforced thermoplastic, self-extinguishing
Length of the wire, maximum	10 m
Gross weight	230 g
Reaction time, maximum	100 ms

Safety appraisal

Standards

IEC 61508

Performance level, up to

Control category to EN13849

PFH-value

1.40 x 10⁻⁸ /h

Note (PFH-value)

up to max. 5,000 switching cycles/year

Safety Integrity Level (SIL), suitable for applications in

Mission Time

20 Year(s)

Mechanical data

Mechanical life, minimum	100,000 Operations
Actuating force, maximum	200 N
Actuating travel	400 mm

Mechanical data - Connection technique

Terminal Connector	Connector plug M12, 4-pole, (A-coding)

Mechanical data - Dimensions

Length of sensor	51 mm
Width of sensor	40.5 mm
Height of sensor	182.5 mm

Ambient conditions

Degree of protection	IP67 to EN 60529
Ambient temperature, minimum	-25 °C
Ambient temperature, maximum	+60 °C
Storage and transport temperature, minimum	-25 °C
Storage and transport temperature, maximum	+85 °C
Relative humidity, minimum	30 %
Relative humidity, maximum	95 %
Note (Relative humidity)	non-condensing non-icing
Resistance to vibrations to EN 60068-2-6	10 … 150 Hz, amplitude 0.35 mm / 5 g
Restistance to shock	15 g / 11 ms
Protection rating	II

Ambient conditions - Insulation value

Rated insulation voltage U_i	32 V
Rated impulse withstand voltage U_imp	0.8 kV
Overvoltage category	III
Degree of pollution to VDE 0100	3

Electrical data

Operating Current	50 mA
Switching principle	Snap switch element
Switching frequency	3,600 /h

Electrical data - AS Interface

AS-i Operating voltage, minimum	18 VDC
AS-i Operating voltage AS-i maximum	31.6 VDC
Note (AS-i Operating voltage)	Protection against polarity reversal

Electrical data - AS-Interface specification

AS-i Version	V 3.0
AS-i Profile	S-0.B.F.F
AS-i, IO-Code	0x0
AS-i, ID-Code	0xB
AS-i, ID-Code1	0xF
AS-i, ID-Code2	0xF
AS-i Input, Channel 1	Data bits DI 0 / DI 1 = dynamic code transmission
AS-i Input, Channel 2	Data bits DI 2 / DI 3 = dynamic code transmission
AS-i Outputs, DO 0 … DO 3	No Function
AS-i Parameter bits, P0	Channel 2 switched
AS-i Parameter bits, P1	No function
AS-i Parameter bits, P2	No function
AS-i Parameter bits, P3	No function
Note (AS-i Parameter bits)	Set the parameter outputs to '1111' (0xF) FID: periphery error
AS-i Input module address	0
Note (AS-i Input module address)	Preset to address 0, can be changed through AS-interface bus master or hand-held programming device

Pin assignment

PIN 1	AS-Interface +
PIN 2	n.c.
PIN 3	AS-Interface -
PIN 4	n.c.

Notes

Note (General)	Recommended cable lengths for pull-wire Emergency-Stop switches in relation to the range of ambient temperature. As the thimbles are subject to deformation in case of wire pull, the wire should be pulled several times after fitting. After that, the wire must be re-tensioned using the eyebolt or the tensioner. The addressing must take place via the M12 connector or the flat cable connection. At 2 mm to 5 mm distance, intermediate wire supports are required, see accessories