ZQ 700 FK-AS | Ланфор

Бренды по алфавиту:

Eng Рус

Производитель: Schmersal GmbH

Артикул: Л-0043766

Работаем с юридическими лицами, бюджетными организациями, ИП

По вопросам приобретения товара пишите на zakaz@lanfor.ru

Оплата по безналичному расчету согласно выставленному счету

Самовывоз - бесплатно, от 300руб. до пункта выдачи в Вашем городе, доставка от 500руб. "до двери"

Certificates	cULus ASi-SaW EAC

Standards	IEC 61508 EN 60947-5-1 EN 50295 EN ISO 13850 EN ISO 13849-1
Enclosure material	Plastic, glass-fibre reinforced thermoplastic, self-extinguishing
Material of the cover	Plastic, glass-fibre reinforced thermoplastic, self-extinguishing
Length of the wire, maximum	10 m
Gross weight	265 g
Reaction time, maximum	100 ms

Standards

IEC 61508

Performance level, up to

Control category to EN13849

PFH-value

1.40 x 10⁻⁸ /h

Note (PFH-value)

up to max. 5,000 switching cycles/year

Safety Integrity Level (SIL), suitable for applications in

Mission Time

20 Year(s)

Terminal Connector	Connection for flat cable

Degree of protection	IP67 to EN 60529
Ambient temperature, minimum	-25 °C
Ambient temperature, maximum	+60 °C
Storage and transport temperature, minimum	-25 °C
Storage and transport temperature, maximum	+85 °C
Relative humidity, minimum	30 %
Relative humidity, maximum	95 %
Note (Relative humidity)	non-condensing non-icing
Resistance to vibrations to EN 60068-2-6	10 … 150 Hz, amplitude 0.35 mm / 5 g
Restistance to shock	15 g / 11 ms
Protection rating	II

Rated insulation voltage U_i	32 V
Rated impulse withstand voltage U_imp	0.8 kV
Overvoltage category	III
Degree of pollution to VDE 0100	3

AS-i Operating voltage, minimum	18 VDC
AS-i Operating voltage AS-i maximum	31.6 VDC
Note (AS-i Operating voltage)	Protection against polarity reversal

AS-i Version	V 3.0
AS-i Profile	S-0.B.F.F
AS-i, IO-Code	0x0
AS-i, ID-Code	0xB
AS-i, ID-Code1	0xF
AS-i, ID-Code2	0xF
AS-i Input, Channel 1	Data bits DI 0 / DI 1 = dynamic code transmission
AS-i Input, Channel 2	Data bits DI 2 / DI 3 = dynamic code transmission
AS-i Outputs, DO 0 … DO 3	No Function
AS-i Parameter bits, P0	Channel 2 switched
AS-i Parameter bits, P1	No function
AS-i Parameter bits, P2	No function
AS-i Parameter bits, P3	No function
Note (AS-i Parameter bits)	Set the parameter outputs to '1111' (0xF) FID: periphery error
AS-i Input module address	0
Note (AS-i Input module address)	Preset to address 0, can be changed through AS-interface bus master or hand-held programming device

Note (General)	Recommended cable lengths for pull-wire Emergency-Stop switches in relation to the range of ambient temperature. As the thimbles are subject to deformation in case of wire pull, the wire should be pulled several times after fitting. After that, the wire must be re-tensioned using the eyebolt or the tensioner. The addressing must take place via the M12 connector or the flat cable connection. At 2 mm to 5 mm distance, intermediate wire supports are required, see accessories